JANUS – Status display

Emitter – JANUS ML / MT

1 Red LED	2 Green LED	3 Yellow LED	Meaning
⊗	⊗	⊗	System power-on – Initial TEST for 5 seconds
⊗	⊗	⊗	Test conditon
⊗	⊗	⊗	GUARD condition
⊗	⊗	⊗	FAIL condition. See next « fail condition table »

1 Red LED	2 Green LED	3 Yellow LED	4 RANGE	Meaning
⊗	⊗	⊗	⊗	System power-on – Initial TEST for 5 seconds
⊗	⊗	⊗	⊗	Test conditon
⊗	⊗	⊗	⊗	GUARD condition
⊗	⊗	⊗	⊗	High range selected
⊗	⊗	⊗	⊗	FAIL condition. See next « fail condition table »

1 Red LED	2 Green LED	3 Yellow LED	4 RANGE	Meaning
⊗ Blinking	⊗	⊗	⊗	Internal fault
⊗ Blinking	⊗	⊗ Blinking	⊗
⊗ Blinking	⊗ Blinking	⊗	⊗
⊗ Blinking	⊗	⊗	⊗ Blinking	Correct the range selection on the Emitter Unit

1 Red LED	2 Green LED	3 Orange LED	4 Clear/Override LED	S1 LED	S2 LED	S3 LED	S4 LED	MUT LED	C Display	Meaning
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	8	System power-on – Initial TEST for 5 seconds

LED	Status	Meaning
S1	⊗	Enabling of timeout 30 s.
S1	⊗	Enabling of timeout 90 min.
S2	⊗	With 4 sensors, enabling of sequential Muting
S2	⊗	With 4 sensors, enabling of concurrent operation mode
S3	⊗	Manual restart functioning mode enabled
S3	⊗	Automatic restart functioning mode enabled
S4	⊗	External relays feedback control enabled
S4	⊗	External relays feedback control disabled
MUT	⊗	Muting configuration with 4 sensors
MUT	⊗	Muting configuration with 2 sensors
1 Red LED	⊗	OSSD outputs set to OFF
4 Clear/Override	⊗	Automatic override with pulse command
4 Clear/Override	⊗	Manual overrun action with hold to run
Display	C	Configuration

LED	Status	Meaning
S1	⊗	Interruption Sensor 1
S1	⊗	Sensor 1 clear
S2	⊗	Interruption Sensor 2
S2	⊗	Sensor 2 clear
S3	⊗	Interruption Sensor 3
S3	⊗	Sensor 3 clear
S4	⊗	Interruption Sensor 4
S4	⊗	Sensor 4 clear
MUT	⊗	Muting active
MUT	⊗	Light curtain active – GUARD condition
1 Red LED	⊗	OSSD outputs set to OFF
2 Green LED	⊗	GUARD condition
3 Orange LED	⊗	Weak signal
4 Clear/Override	⊗	Light curtain in override, OSSD outputs set ON. « o » letter appears on the display and at the same time the external Muting/Override lamp blinks.
4 Clear/Override	⊗ Blinking	Override request
Display	–	During normal functioning
Display	F – Code	Fault detected. Displayed alternatively to the error code. See next « Fail condition Table »

Configuration errors

C: Incorrect configuration of the system (the flashing led together with the C indicates the incorrect type of configuration). See Technical manual
L: Muting light not present or fault
U: Incorrect « SYSTEM STATUS » or overload signal connection
E: External contact enabling/disabling signal missing or contactors feedback missing
II: Unstable Muting sensors signals or Barrier configured for 2 sensors but found 3 or 4 sensors (the corrispondent led flashes)

Faults

1 Red LED	2 Green LED	3 Orange LED	4 Clear/Override LED	MAN/AUTO LED	EN EDM LED	C Display	Meaning
⊗	⊗	⊗	⊗	⊗	⊗	8	System power-on – Initial TEST for 5 seconds

LED	Status	Meaning
MAN/AUTO LED	⊗	Manual restart functioning mode enabled
MAN/AUTO LED	⊗	Automatic restart functioning mode enabled
EN EDM LED	⊗	External relays feedback control enabled
EN EDM LED	⊗	External relays feedback control disabled
1 Red LED	⊗	OSSD outputs set to OFF
Display	C	Configuration

LED	Status	Meaning
1 Red LED	⊗	OSSD outputs set to OFF
2 Green LED	⊗	GUARD condition
3 Orange LED	⊗	Weak signal
4 Yellow LED	⊗	Light curtain clear, OSSD outputs set OFF (the receiver is waiting for a Restart signal)
Display	–	Normal functioning
Display	F – CODE	Fault detected. Displayed alternatively to the error code. See next « Fail condition Table »

Configuration errors

C: Incorrect configuration of the system (the flashing led together with the C indicates the incorrect type of configuration). See Technical manual
E: External contact enabling/disabling signal missing or contactors feedback missing

Faults