SAFEGATE – Status display

Emitter – All models

Three colour LED	Meaning
⊗	System power-on – Initial TEST
⊗ Blinking	FAIL condition – The type of fault is identified by the number of flashes – See next „Fail condition table“
⊗	TEST condition
⊗	Normal operating condition

Fail condition

Three colour LED	Nr Flashes	Meaning
⊗	2 consecutive	RANGE0 / RANGE1 wrong wiring
⊗	3/4 consecutive	Internal falilure
⊗	5 consecutive	SYNC wrong wiring

 

Receiver – All models with muting functions

1 PRG LED	2 COM/WEAK LED	3 CLR LED	4 Two colour LED	5 MUT LED	6 OVR LED	7 S1 LED	8 S2 LED	9 S3 LED	10 S4 LED	Meaning
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Curtain programmed via USB
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Communication with active PC
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Weak signal (14 mm and long range models only)
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Curtain awaiting RESTART (clear gate)
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Normal operation
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Occupied gate
⊗	⊗	⊗	⊗ Blinking	⊗	⊗	⊗	⊗	⊗	⊗	FAIL condition – The type of fault is identified by the number of flashes – See next „Fail condition table“
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Muting active
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Override active
⊗	⊗	⊗	⊗	⊗	⊗ Blinking	⊗	⊗	⊗	⊗	Override request
⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	Muting sensors interrupted
⊗ Blinking	⊗ Blinking	⊗	⊗	⊗	⊗	⊗	⊗	⊗	⊗	No barrier programmation
⊗ Blinking	⊗ Blinking	⊗	⊗ Blinking	⊗	⊗	⊗	⊗	⊗	⊗	Detected double programmation (hardware and software)

 

Fail condition

3 CLR LED Nr. flashes	4 Two colour LED Nr. fleshes	5 MUT LED Nr. fleshes	6 OVR LED Nr. fleshes	7 S1 LED	8 S2 LED	9 S3 LED	10 S4 LED	Meaning
⊗	⊗ 2	⊗	⊗	⊗	⊗	⊗	⊗	Configuration error SEL_A/SEL_B/EDM
⊗	⊗ 2	⊗	⊗	⊗ 2	⊗ 2	⊗	⊗	Inconsistency between red and blue connector selection for S2 wiring and the physical wiring of S2
⊗	⊗ 3	⊗	⊗	⊗	⊗	⊗	⊗	Wrong EDM configuration
⊗ 3	⊗ 3	⊗	⊗	⊗	⊗	⊗	⊗	EDM feedback failure
⊗	⊗ 3	⊗ 3	⊗	⊗	⊗	⊗	⊗	STATUS input failure
⊗	⊗ 3	⊗	⊗ 3	⊗	⊗	⊗	⊗	OVERRIDE_1 / OVERRIDE_1 input failure
⊗	⊗ 3	⊗	⊗	⊗ 3	⊗ 3	⊗ 3	⊗ 3	SENSOR input failure
⊗ 3	⊗ 3	⊗ 3	⊗ 3	⊗	⊗	⊗	⊗	MUTING LAMP FAILURE
⊗	⊗ 4	⊗	⊗	⊗	⊗	⊗	⊗	OSSD1 / OSSD2 error
⊗	⊗ 5	⊗	⊗	⊗	⊗	⊗	⊗	MAIN CARD ERROR
⊗ 5	⊗ 5	⊗	⊗	⊗	⊗	⊗	⊗	BASE SHEET (EEPROM) error
⊗	⊗ 5	⊗	⊗ 5	⊗	⊗	⊗	⊗	MAIN CARD ERROR
⊗	⊗ 6	⊗	⊗	⊗	⊗	⊗	⊗	MAIN CARD (Microcontroller) error
⊗ 6	⊗ 6	⊗	⊗	⊗	⊗	⊗	⊗	GENERIC DEFAULT BOARD ERROR
⊗	⊗ 6	⊗ 6	⊗	⊗	⊗	⊗	⊗	Beam error
⊗	⊗ 6	⊗	⊗ 6	⊗	⊗	⊗	⊗	24VDC power supply overload
⊗	⊗ 6	⊗ 6	⊗ 6	⊗	⊗	⊗	⊗	LAMP/STATUS over current
⊗	⊗ 7	⊗	⊗	⊗	⊗	⊗	⊗	Receiving beams failure
⊗	⊗ 8	⊗	⊗	⊗	⊗	⊗	⊗	Interfering Emitter Detected

 

 

Receiver – All models without Muting functions

 

2. WEAK LED	3. CLR LED	4. Two colour LED	Meaning
⊗	⊗	⊗	Weak signal (14 mm and long range models only)
⊗	⊗	⊗	Curtain awaiting RESTART (clear gate)
⊗	⊗	⊗	Normal operation
⊗	⊗	⊗	Occupied gate
⊗	⊗	⊗ Blinking	FAIL condition – The type of fault is identified by the number of flashes – See previous „Fail condition table“